Welcome to Emulationworld

Forum Index | FAQ | New User | Login | Search

Make a New PostPrevious ThreadView All ThreadsNext ThreadShow in Flat Mode*

SubjectRe: NES Emulator: Where does the instruction pointer start in a ROM? Reply to this message
Posted byklipseracer
Posted on02/01/08 00:24 AM


Here is the code:

// Initialize the registers to their values.
CPU.A = 0;
CPU.X = 0;
CPU.Y = 0;
CPU.S = 0;
CPU.F = 0;
CPU.P = MAKEWORD(GetMemoryByte(0xFFFC), GetMemoryByte(0xFFFD));

// Zero all the memory.
ZeroMemory(CPU.Memory, 0x8000);

// Reset the number of cpu cycles until the next scanline.

// Now display the updated information.

return S_OK;
} // end ResetNES()

And here is the GetMemoryByte() code:

BYTE __stdcall GetMemoryByte(WORD wAddress)
if (wAddress >= 0x8000 && wAddress < 0xC000)
return CPU.pbyPRGROMBank1[wAddress-0x8000];
else if (wAddress >= 0xC000 && wAddress <= 0xFFFF)
return CPU.pbyPRGROMBank2[wAddress-0xC000];
return CPU.Memory[wAddress];
} // end GetMemoryByte()

That is the code i'm using, credit goes to the author of Nestreme, but now I understand how it works and why it uses the MAKEWORD macro. the address it starts from is a 16bit address, this suddenly makes more sense. Thanks a lot! Now I just need to understand the mappers a little better which would help me out here. I can load most roms until 0xC000 and read the opcodes correctly, but I think C000 is where the page ends and I need to figure out how to correctly load the rom into memory.

Also, In this scenario, it will return an address in the PRGRomBank2 right?

> I think you need to distinguish between the ROM file, which is essentially a
> dump of the ROM chips on the cartridge plus a header tacked on, and the 6502
> address space, which is only 64KB total. Obviously, some of that 64KB has to be
> mapped to RAM and hardware registers and only a fraction to ROM. Therefore, the
> cartridges often provide a hardware mechanism (so-called "mappers") to change
> (or "map") the chunk of ROM that is visible to the 6502.
> According to the documentation I'm looking at, for a MOS 65CE02, the reset
> vector is at FFFC. The low 8 bits of the program counter are loaded from there,
> and the high 8 bits from FFFD. From what I recall, the cartridge ROM space
> appears somewhere in the upper address space of the 6502, which would cover
> these vectors. Therefore, you should ensure that you are mapping the cartridge
> appropriately here.
> You'll have to consult more documentation on the NES as well as the mapper that
> the game(s) in question use.
> > I have a NES emu project in its beginning stages, I can read the 16byte
> headeer
> > correctly and find out how many pages of prg and chr rom it has, and I can
> setup
> > the 2 prg rom banks and all that. But where do I start reading opcodes from? I
> > know its in the PRG-ROM somewhere. I was told FFFEh? But that is outside of
> the
> > allocated PRG-ROM memory range. I'm just trying to fetch the first opcode,
> which
> > i'm having trouble doing. If someone could tell me the default Program
> > counter/instruction counter address, it would be greatly appreciated!
> >
> ----
> Bart

Entire Thread
Subject  Posted byPosted On
*NES Emulator: Where does the instruction pointer start in a ROM?  klipseracer01/26/08 01:44 PM
.*Re: NES Emulator: Where does the instruction pointer start in a ROM?  Bart T.01/26/08 05:09 PM
...Re: NES Emulator: Where does the instruction pointer start in a ROM?  klipseracer02/01/08 00:24 AM
...*Re: NES Emulator: Where does the instruction pointer start in a ROM?  Bart T.02/01/08 02:57 AM